Use of Cookies

We use our own cookies and third-party analytical cookies to analyze your browsing habits and offer you content based on your interests. Please refer to our Cookie Policy for more information. By clicking 'Accept,' you acknowledge that you have been informed and consent to the installation and use of cookies. You can also configure or reject their use by clicking here.
Cookies policy

Below you can configure your preferences and choose which cookies you allow to be installed on your device by clicking the "Accept" button or by denying their installation with the "Reject" button, either individually or globally:

TECHNICAL COOKIES

These cookies are necessary for the website to function and cannot be disabled in our systems.
ANALYTICAL COOKIES
STATISTICAL COOKIES

For more information, see our Cookie Policy
Product out of catalogue

BOX BV PLUS 18/18 3kW 950RPM+CPCR M 2+G4 PL+ePM1≥50% MD+H13 CM (SUPPLY) (Galv. Impeller)

Model
CPCR M 2 (1225x614x900)
Code
CPCR1225900
Information
DRAWER HOLDER FOR RECTANGULAR DUCT

Drawers with 1, 2 or 3 stages of in-line filtration for rectangular ducts.

MANUFACTURING FEATURES

• 1mm thick galvanized steel box.
• Suitable for medium and high efficiency filters from IISO Coarse≥60% (G4) up to ePM1≥80%(F9).
• The CPCR is available in 2 sizes (S and M) that allow to combine up to 3 different filtration stages, varying only the length of the boxes.
• The height of boxes is always the same. With two in-line S boxes it would be possible to make a CPCR L for 3 stages of filtration with bag filters.
• The CPCR allows duct mounting for all types of filters (compact, dihedral, bags).

UNDER REQUEST

• Stainless steel or painted steel.
• Outdoor mounting: with outdoor flange and cowl.
• Flat or conical connections to adapt the CPCR to a circular duct.
• Assembly of drawers in battery (horizontal or vertical).
• Active Carbon Filters (CA).
• ATEX version: only for the 1 and 2 stage filtration versions. With grounding and equipotential bonding of all the elements of the drawer (The filters are ATEX specific with antistatic polyester frames).

Model
FILT ISO Coarse≥60% (592x592x48) PREFILTRO MARCO CHAPA
Code
FILTG04026
Information
CELL FILTER WITH GALVANIZED FRAME

Filter cells for rough primary filtration for air treatment units or air intake grids.

• Thick synthetic media with high retention capacity pleated between 2 rigid screens.
• Large filter surface.
• Frame: galvanised,

• Maximum continuous operating temperature: 70°C
• Relative humidity: 100%

• Tested for food contact according to EC 1935/2004

Model
FILT ePM1≥50% (592x592x292) ALTA EFIC. EN V MINIPLEGADO
Code
FILTF07015
Information
RIGID AND COMPACT FILTER WITH HIGH EFFICIENCY AND LOW PRESSURE DROP

Filtration for air treatment units equipped with a pre-filter upstream in white-rooms.

Low pressure drop, high efficiency, compact and economic filter.

• Media: Mini pleat fiberglass paper
• Frame: Polystyrene
• Separator: hot-melt beads
• Sealant: Polyurethane

• Maximum T° in continuous service: 70°C
• Humidity: 100% RH

• Tested for food contact according to CE 1935/2004
• Certified for microbial development (ISO 846-VD 6022)

Model
FILT H13 (610x610x292) ABSOLUTO FLUJO TURBULENTO
Code
FILTH13002
Information
ABSOLUTE FILTER FOR TERMINAL FILTRATION AND DRAWERS

• Terminal filtration in air treatment units for clean or white room applications and extraction boxes for dangerous and toxic contaminants (asbestos).
• Large air flow with very low initial pressure drop. Solid execution and great finish.
• Mini-folded fibreglass paper stocking.
• Galvanized steel frame.
• Sealant: polyurethane.
• Separator: continuous thermoplastic cords.
• Gasket: Half round monoblock polyurethane.
• Maximum temperature in continuous service 80ºC.
• Relative humidity 70-80%.
• Approved for contact with food according to CE 1935/2004.
• Certified against microbial growth (ISO 846-VD 6022).

Please confirm

frontend.are_you_sure